Fiberlock IAQ 6000 is a white, tintable mold resistant coating for professional use, that contains a fungistatic agent to resist mold growth on the dry coating surface. IAQ 6000 is a durable, flexible, and permeable 100% acrylic water based coating. IAQ 6000 has been tested by independent and certified laboratories to prove resistance to mold growth on the surface of the coating, and has successfully passed both ASTM G-21 and ASTM D-3273 mold resistance testing with the highest scores possible. IAQ 6000 is recommended for use on wood, plaster, wallboard, sheetrock, concrete, masonry block, primed metal and galvanized metal. IAQ 6000 can also be used on new structural materials during building construction.
- Tested by independent laboratories for mold resistance: ASTMG-21 and ASTM D-3273
- Mold resistant*
- Tintable formula
- 100% acrylic
Surfaces to be coated must be free of dust, mildew, mold, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap and other surface contamination. Clean mold stained surfaces with Advanced Peroxide Cleaner, or use an EPA registered antimicrobial disinfectant cleaner such as IAQ 2000, IAQ 2500, ShockWave or ShockWave RTU. Patch irregularities with vinyl patching paste or an appropriate patching compound. IAQ 6000 is self-priming over bare sheetrock, composition board, ceiling tile and concrete.
WALLBOARD, SHEETROCK, GYPSUM BOARD: Joint cement should be sanded smooth, but avoid abrading the paper.
FERROUS METAL: Clean, then prime with IAQ 4000 rust inhibiting direct-to-metal primer.
WOOD: Seal knots and stains with IAQ 5000 stain-blocking primer.
MASONRY BLOCK: Apply one coat of IAQ 3000 block filler if a denser surface is desired.
Apply IAQ 6000 with brush, roller or airless spray equipment.
Brush: Synthetic, nylon or polyester bristle
Roller: Synthetic fiber 3/8” nap or longer
Spray Settings Pressure: 2000-3000 P.S.I.
Tips: .019 to .021 tips
IAQ 6000 may be tinted to any off-white or pastel based color. Add up to 2 oz. of universal colorant per gallon. Start with 50% of the tinting formula and adjust as necessary.
IAQ 6000 is supplied ready to use, but can be thinned sparingly with water (up to 1/2 pint water per gallon) for proper application consistency if necessary. Apply IAQ 6000 generously and uniformly by brush, roller, or airless spray. Apply one coat of IAQ 6000 and ensure that the finished surface is properly sealed. To ensure that the finished surface is properly sealed, two-coats may be required on some porous surfaces.
Smooth Surfaces- 250-400 sq. ft. per gallon
Porous Surfaces- 150-300 sq. ft. per gallon
DRYING TIME: @ 70°F 50% R.H
To Touch – 1 Hour
Recoat – 4 Hours
Clean tools and drippings with warm soapy water before Fiberlock IAQ 6000 dries. Dispose of all waste according to all existing local, state and federal regulations.
Store in a dry place at temperatures between 40°F (4.5°C) and 90°F. (32°C). Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil. The IAQ 6000 coating is resistant to mold only on the surface of the coating. No mold resistance claim is made other than to the coating itself. The use of this product does not protect users or others against food-borne or disease-causing bacteria, viruses, germs or other disease-causing organisms. Do not apply when air or surface temperature is below 50°F, or when drying conditions are poor or when surfaces are above a 15% moisture level content. Use adequate ventilation during application. When applying with a sprayer, wear a NIOSH approved respirator with any R, P, N or HE filter. For interior use only.
Solids by Weight +/- 2% 54.6%
Solids by Volume +/- 2% 39.6%
Viscosity at 70°F 90-95 Kreb Units
Flash Point Non-combustible
Shelf Life 36 Months min original sealed container
Calculated VOC 65 grams/liter
Water Vapor Permeance 3.7 perms
Available Package Sizes: 5 Gallon Containers, weight 11.1 lbs/gallon
*Resistant to mold growth on the dry coating surface only
KEEP OUT OF REACH OF CHILDREN.
Do not take internally. Close container after each use.
Keep from freezing.
Store between 40°F (4.5°C) and 90°F. (32°C)
24 hour Emergency “CHEM-TEL” - 800.255.3924